The location of the 1 pin (first pin) on an IDE cable is usually designated by the red stripe on one side of the cable. In the example picture above, the 1 pin is on the right side of the cable..
Consequently, how do you connect a ribbon cable to a connector?
Connecting Ribbon Cables Connecting the ribbon cable is simply a matter of lining up the grooves and ridges, then pressing the cable down into the connection socket. If the cable encounters resistance, it should be checked to make sure that the ridges aren't on the wrong side of the socket.
Secondly, where is the pin 1 indicator on the drive connector? The pin 1 indicator on the drive connector is usually closest to the power connector on the drive. Many older motherboards have two PATA drive controllers, providing support for a maximum of four PATA drives. The SATA data cable has a 7-pin connector.
Subsequently, question is, how can you tell which side of a hard drive data cable connects to pin 1 on the drive?
Look for a label on the board around the connector. It may be called Pin 1, or it may simply show a 1 and 2. Other possibilities include 39 and 40, or 33 and 34, which would mean you would find Pin 1 at the other end.
What are ribbon cable connectors called?
Popular types of connectors available with IDC termination suitable for ribbon cable include. BT224 connector – also defined by BS9525-F0023, DIN41651, MIL-C-83503 standards; these are the type used on ATA cables and are often simply called "IDC connectors".
Related Question Answers
How do you release a ribbon cable connector?
To remove it, use a spudger or fingernail to lift the clear blue tab away from the connector. Next, use the tip of the spudger to push open the plastic locking tab. The locking tab will only move about 2 mm. Pull the ribbon cable out of the connector in the direction of the cable.How do you unplug a SATA cable?
Re: Disconnecting SATA cables Well to safely remove the cable you have to place your thumb over the metal piece while your index finger holds the underside of the SATA cable. Then you pinch your thumb and finger together and then you pull the cable out.What is FFC FPC connector?
FFC, FPC (Flat Flex) Connectors Digi-Key offers Flat Flex Connectors (FFC) that include a wide variety of high-density connectors designed for automated assembly. Flexible printed cables (FPC) are ideal where small centerline spacing makes larger wire-to-board solutions impractical.How do ribbon connectors work?
IDE devices use a ribbon cable to connect to each other. Ribbon cables have all of the wires laid flat next to each other instead of bunched or wrapped together in a bundle. There is a connector at each end of the cable and another one about two-thirds of the distance from the motherboard connector.What is the 8 pin connector on a hard drive for?
A jumper pin is a rectangular connector that creates a circuit between two pins. Seagate SATA drives have four pins, while Western Digital SATA drives have eight pins, with the additional pins to be used by technicians or your network administrator for powering up the drive while in standby mode.How do you find the pin 1 on a ribbon cable?
Pin 1 on a ribbon cable is easily identified by the colored stripe that runs down the edge of the cable. Just as every cable has a pin 1, all connectors on devices, adapters, or motherboards have a pin 1. Pin 1 on a cable inserts into pin 1 on a connector. Cables are normally keyed so that they insert only one way.How many pins does a standard IDE connector have?
The two most common types of IDE ribbon cables are the 34-pin cable used for floppy drives and the 40-pin cable for hard drives and optical drives.What are the jumpers for on a SATA HDD?
On SATA-II drives, a jumper is sometimes used to set the drive into SATA-I mode for compatibility with older controllers. Some SATA drives have jumpers to enable/disable 3Gb/s functionality or other backwards compatibility items. See for example this. On a Seagate ST3500320AS, there are four pins in the jumper block.How many pins does a hard drive have?
44-pin IDE/ATA Connections for 2.5" Laptop Hard Drives The first 40 are the same as their desktop cousins but there are an additional four pins (41 to 44) which use 5V power normally carried by a molex connector on a desktop hard drive.What is PATA cable?
Parallel ATA (Parallel Advanced Technology Attachment or PATA) is a standard for connecting hard drives into computer systems. As its name implies, PATA is based on parallel signaling technology, unlike serial ATA (SATA) devices that use serial signaling technology. The cable for a SATA connection has seven conductors.Why do IDE hard drives require jumpers?
You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. You enable particular settings by placing a jumper shunt onto specific pins—creating an electrical circuit between them.What are some of the settings that can be configured using jumpers?
Jumpers are used to configure the settings for computer peripherals, such as the motherboard, hard drives, modems, sound cards, and other components. For example, if your motherboard supported intrusion detection, a jumper can be set to enable or disable this feature.How many pins are there in the motherboard connector?
An ATX power supply provides a number of peripheral power connectors and (in modern systems) two connectors for the motherboard: an 8-pin (or 4+4-pin) auxiliary connector providing additional power to the CPU and a main 24-pin power supply connector, an extension of the original 20-pin version.What does a stripe on the data cable indicate?
What is the red stripe? The red stripe on ribbon cables is used to indicate that this is pin 1 of the cable. When using this type of cable, it is important that pin 1 is plugged into pin 1 one the device, and pin 1 on the motherboard or other device.What type of power connector does the heatsink fan assembly usually have?
The heat sink/fan assembly usually has a 3-pin power connector.How is pin 1 identified on the front panel cables?
Explanation: Each cable that connects to the front panel connector on the motherboard is marked with a small arrow to identify which pin is pin 1 so that it can be aligned with pin 1 on the panel.What provides the data for the floppy drive?
A floppy disk, also known as a floppy, diskette, or simply disk, is a type of disk storage composed of a disk of thin and flexible magnetic storage medium, sealed in a rectangular plastic enclosure lined with fabric that removes dust particles. Floppy disks are read and written by a floppy disk drive (FDD).What form factor does your computer use?
1) In computers, the form factor is the size, configuration, or physical arrangement of a computing device. The term is commonly used in describing the size and/or arrangement of a device, acomputer case or chassis or one of its internal components such as a motherboard or a daughterboard.What components defines the system's form factor?
What component(s) defines the system's form factor? The form factor is a set of specifications for the size, shape, and configuration of the components that make up a computer system. Sharing a common standard allows components such as the case, motherboard, and power supply to together and function properly. 
